焊煙集中收集濾筒除塵器采用先進的褶皺式濾筒為過濾元件，可除去細小的非纖維性粉塵，該機與傳統的脈沖袋式除塵器相比，具有體積小、過濾面積大、除塵效率高、壓力損失低、運行可靠、使用壽命長等優點。廣泛用于機械加工、焊接煙塵鑄造、化工、陶瓷、制動材料加工、噴粉等行業的粉塵治理和回收以及鑄造的凈化，塵氣處理后達到排放標準，是脈沖除塵器的新形式。

The welding smoke centralized collection filter cartridge dust collector adopts advanced folded filter cartridges as filtering elements, which can remove small non fibrous dust. Compared with traditional pulse bag dust collectors, this machine has advantages such as small volume, large filtering area, high dust removal efficiency, low pressure loss, reliable operation, and long service life. Widely used for dust control and recovery in industries such as mechanical processing, welding dust casting, chemical engineering, ceramics, brake material processing, powder spraying, and purification of casting. After dust gas treatment, it meets emission standards and is a new form of pulse dust collector.

工作原理

working principle

含塵氣體由位于除塵器上部的進風口進入除塵器箱體，由上下行，由于重力與下行氣流的作用首先把塵粒直接降至灰斗，細粉塵被濾筒捕集在外表面，潔凈氣體經濾筒過濾凈化后，由濾筒中心進入清潔室，再經下出風口排出。隨著過濾工況持續，聚集在濾筒表面的粉塵增多，此時脈沖控制儀按設定的脈沖周期和脈沖間隔控制電磁閥開啟，噴出高壓氣體，吹入濾筒內腔，抖落外表積塵，落入灰斗，經卸灰口排出。

Dust containing gas enters the dust collector box from the air inlet located at the upper part of the dust collector, and from top to bottom. Due to the effect of gravity and downward airflow, the dust particles are first directly lowered into the ash hopper, and fine dust is captured on the outer surface by the filter cartridge. After the clean gas is filtered and purified by the filter cartridge, it enters the clean room from the center of the filter cartridge and is then discharged through the lower air outlet. As the filtering condition continues, the dust that accumulates on the surface of the filter cartridge increases. At this time, the pulse control instrument controls the solenoid valve to open according to the set pulse cycle and pulse interval, spraying high-pressure gas into the inner chamber of the filter cartridge, shaking off the dust on the surface, and falling into the ash hopper, which is discharged through the ash discharge port.

結構特點

Structural characteristics

除塵器內部濾芯采用快插式安裝拆卸比較方便，工人只需在除塵器外部操作即可。不需要人員鉆入除塵器，杜絕了拆卸維護時的困難。

The internal filter element of the dust collector adopts a quick plug-in installation and disassembly method, which is more convenient. Workers only need to operate outside the dust collector. No need for personnel to drill into the dust collector, eliminating the difficulty of disassembly and maintenance.

2，多道防火星措施，直接設計在除塵器內部，可以節省外連接防火星裝置。使其使用更加安全可靠，杜絕了客戶的后顧之憂。

2. Multiple fire star measures, directly designed inside the dust collector, can save external connection to the fire star device. Make its use safer and more reliable, eliminating customers' worries.

3，除塵器內部濾芯采用全方位旋轉清灰，使清灰更加徹底干凈，能始終保證除塵器具有一個的通氣量，且提高了整機的使用壽命。

3. The internal filter element of the dust collector adopts all-round rotation for dust cleaning, making the dust cleaning more thorough and clean. It can always ensure that the dust collector has a certain ventilation capacity and improve the service life of the entire machine.

4，除塵器控制系統采用自動控制，使工人操作更加方便靈活。

4. The dust collector control system adopts automatic control, making workers' operations more convenient and flexible.

焊煙集中收集濾筒除塵器濾材的清潔通過由壓差傳感器控制的脈沖噴吹機構實現：當凈化器運行一段時間以后，細微的煙塵吸附在濾材表面，使得濾材的透氣性降低。壓差傳感器的兩個探測頭一個安裝在原氣側、一個安裝在凈氣側。當壓差傳感器檢測到的壓差超過某一設定值時輸出壓差信號，脈沖發生器接收信號后順序啟動脈沖噴吹閥，潔凈的壓縮空氣由閥口噴出，引射氣流對濾筒進行吹掃直到壓差低于另一設定值時才停止；濾材表面吸附的微塵在氣流作用下被清除，落在室體下部的集塵斗中。脈沖噴吹需0.5～0.6MPa的潔凈壓縮空氣，且運行中須保持連續且恒定不變的供氣量。濾筒式過濾器與傳統靜電式過濾器、機械式過濾器相比有如下優點：排放濃度低，達5mg/m3,一般其他過濾器只能過濾0.5um以上粒徑;而我司產品能過濾0.3um以上的粉塵。透氣性好，氣阻比一般過濾器低;清灰方便，全自動清灰，保證生產的連續性和高效性。粉塵收集，容器裝卸便捷，與過濾漏斗的連接是密封的，不漏灰塵。

The cleaning of the filter material of the welding smoke centralized collection filter cartridge dust collector is achieved through a pulse blowing mechanism controlled by a pressure difference sensor. After the purifier runs for a period of time, fine smoke and dust adsorb on the surface of the filter material, reducing its breathability. The two detection heads of the pressure difference sensor are installed on the raw gas side and one on the clean gas side. When the pressure difference detected by the pressure difference sensor exceeds a certain set value, a pressure difference signal is output. After receiving the signal, the pulse generator sequentially starts the pulse blowing valve, and clean compressed air is sprayed out from the valve port. The injected airflow blows the filter cartridge until the pressure difference is lower than another set value before stopping; The fine dust adsorbed on the surface of the filter material is removed by the airflow and falls into the dust collection hopper at the lower part of the chamber. Pulse injection requires clean compressed air of 0.5~0.6MPa and a continuous and constant air supply during operation. Compared with traditional electrostatic and mechanical filters, cartridge filters have the following advantages: low emission concentration, up to 5mg/m3, and generally other filters can only filter particles with a diameter of more than 0.5um; And our product can filter dust above 0.3um. Good breathability, lower air resistance than ordinary filters; Convenient ash cleaning, fully automatic ash cleaning, ensuring continuous and efficient production. Dust collection, convenient container loading and unloading, and sealed connection with the filter funnel to prevent dust leakage.

焊煙集中收集濾筒除塵器過濾濾材特點

Characteristics of Filter Materials for Welding Smoke Centralized Collection Filter Cartridge Dust Remover

焊煙集中收集濾筒除塵器采用高效過濾筒作為過濾元件，該過濾筒選用的濾材不同于一般傳統的濾材，其表面附有一層聚四氟乙烯薄膜。傳統濾材（如棉布、棉緞、紙質及其他傳統纖維素等）纖維間隙為5～60um，當煙塵通過時，煙塵中的一部分塵粒就會進入濾材內部而阻塞過濾元件；當阻塞情況逐漸惡化又不能進行有效清灰時，過濾元件的氣阻便會上升，能通過的氣流量也會隨之下降。如果沒有自動清灰，過濾效果會迅速下降，而該系列凈化器采用的濾材表面附有一層聚四氟乙烯薄膜，其極小的篩孔可阻擋大部分亞微米塵粒；亞微米塵粒在濾材的表面聚集并形成可滲透的擋塵餅，大部分塵粒被阻擋在濾材外表面而不能進入濾材內部，在壓縮空氣的吹掃下能及時有效地被清除。該濾材具有相當高的過濾效率，較傳統濾材至少提高3～5倍以上；且使用壽命較傳統濾材提高2倍以上

The welding smoke centralized collection filter cartridge dust collector uses an efficient filter cartridge as the filtering element. The filter cartridge uses a different filter material from traditional filters, with a layer of polytetrafluoroethylene film attached to its surface. Traditional filter materials (such as cotton cloth, cotton satin, paper, and other traditional cellulose) have a fiber gap of 5-60um. When smoke passes through, a portion of the dust particles in the smoke will enter the filter material and block the filter element; When the blockage situation gradually deteriorates and effective ash removal cannot be carried out, the air resistance of the filtering element will increase, and the air flow rate that can pass through will also decrease. If there is no automatic dust removal, the filtering effect will rapidly decrease, and the filter material used in this series of purifiers has a layer of polytetrafluoroethylene film attached to its surface, which has extremely small sieve holes that can block most of the submicron dust particles; Submicron dust particles gather on the surface of the filter material and form permeable dust blocking cakes. Most of the dust particles are blocked on the outer surface of the filter material and cannot enter the interior of the filter material. They can be timely and effectively removed under the blowing of compressed air. This filter material has a relatively high filtration efficiency, which is at least 3-5 times higher than traditional filter materials; And the service life is more than twice that of traditional filter materials

焊煙除塵器的除塵過程，集中式焊煙除塵器主要是針對治理在機械加工、鑄造廠、粉料回收、醫療生產、食品加工，焊接煙塵、切割、打磨、家具生產等行業生產時產生大量對人體有害的粉塵顆粒而設計的，處理風量4000~60000m/h，不同的組合滿足不同風量的處理要求，可滿足生產車間多工序的粉塵收集處理，收集方式有移動吸臂式和固定收集罩等，程度減少粉塵逸散到車間內，保障車間工作環境?？蓛艋罅繎腋≡诳諝庵袑θ梭w有害的粉塵顆粒。

The dust removal process of welding fume dust collectors is mainly designed for the treatment of a large number of harmful dust particles generated during production in industries such as mechanical processing, foundry, powder recycling, medical production, food processing, welding fume, cutting, polishing, furniture production, etc. The processing air volume is 4000-6000m/h, and different combinations meet the processing requirements of different air volumes, It can meet the requirements of dust collection and treatment in multiple processes in the production workshop. The collection methods include mobile suction arms and fixed collection covers, which minimize the escape of dust into the workshop and ensure the working environment in the workshop. It can purify a large number of dust particles suspended in the air that are harmful to the human body.

焊煙除塵器的產生煙塵和粉塵的凈化以及對稀有金屬、貴重物料的回收等，可凈化大量懸浮在空氣中對人體有害的細小金屬顆粒，擁有非常高的凈化功能，它的濾芯采用自動旋轉反吹清灰，使濾芯表面清灰更加徹底、干凈，能始終保證除塵器擁有一個恒定的吸風量；

The purification of smoke and dust generated by the welding smoke dust collector, as well as the recovery of rare metals and precious materials, can purify a large number of small metal particles suspended in the air that are harmful to the human body. It has a very high purification function, and its filter element adopts automatic rotation reverse blowing to clean the dust, making the surface of the filter core more thorough and clean, and always ensuring that the dust collector has a constant suction air volume;

本文由焊煙除塵設備進行編寫，想要了解更多的產品及更詳細的精彩內容，請關注我們的網站:http://www.a5mp3.com 我們將為您呈現更多的內容。

This article is written by welding smoke dust removal equipment. For more products and detailed exciting content, please follow our website: http://www.a5mp3.com We will present more content for you.